Just how do you feel with regards to How to Install a Bathtub Yourself?
Installing a tub isn't specifically brain surgery, however it does call for strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the task can move immediately; if you have to open up a wall to eliminate the old bathtub as well as place the new tub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will require a helper to leave the old tub and embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. As opposed to employing a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This short article will aid you set up a new bathtub in your washroom if you have currently purchased a new tub and also don't need to alter the arrangement of your previous supply of water pipelines.
Your tools as well as material list need to make up the following:
Planning for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted accessibility that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bathtub until the spirit level checks out degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and examine all joints and brand-new pipework for leaks as well as tighten them if required. Load the tub as well as likewise inspect the overflow outlet and also the typical electrical outlet for leaks.
Lastly, fix the bath paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has been used a minimum of when as this will certainly resolve it right into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers are in location between the faucet as well as the sink. Protect the faucet in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former kind ought to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, resulting in issues with dampness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our post on How to Install a Bathtub. Thanks for taking time to browse our post. Are you aware of anybody else who is very much interested in the topic? Be sure promote it. We take joy in reading our article about How to Install a Bathtub Yourself.
Professional service available.